Attach An Awning Ledger Board To A Wood Siding House

Stratton Bracket Advantages In 2020 Building A Deck Deck With Pergola Diy Deck

Stratton Bracket Advantages In 2020 Building A Deck Deck With Pergola Diy Deck

How To Attach Pergola To House Google Search Attached Pergola Pergola Canopy Wooden Pergola

How To Attach Pergola To House Google Search Attached Pergola Pergola Canopy Wooden Pergola

Fastening A Patio Roof To The House Hometips Building A Patio Pergola Attached To House Building A Deck

Fastening A Patio Roof To The House Hometips Building A Patio Pergola Attached To House Building A Deck

Ledger Board Attachment To Brick Siding Building A Deck Brick Siding Diy Deck

Ledger Board Attachment To Brick Siding Building A Deck Brick Siding Diy Deck

Inspecting A Deck Illustrated Masonry Wall Masonry Building A Deck

Inspecting A Deck Illustrated Masonry Wall Masonry Building A Deck

How To Install A Ledger Building A Deck Diy Deck Deck Construction

How To Install A Ledger Building A Deck Diy Deck Deck Construction

How To Install A Ledger Building A Deck Diy Deck Deck Construction

If your siding is not beveled you can simply screw the ledger tightly to it.

Attach an awning ledger board to a wood siding house.

A ledger relies on the fasteners and strength of the wood ledger board and rim board of the house to carry the deck live and dead loads. If necessary use a sliding bevel to determine angles needed where the rafters will meet the ledger board. Most house framing relies on building elements floors walls roofs being stacked one atop another. Attaching a deck ledger securely is only half the work of installing a ledger.

Attach 2x6 rafters to the house with joist hangers and or supported by the ledger board. If you have beveled horizontal siding then use an inverted piece of siding as shown in the illustration here to create a plumb flat surface for attaching the ledger. Dia galvanized or stainless steel lag screws in every other joist space alternating up and down positions to keep the ledger from splitting. Rafters are placed on 24 centers and attached to the beams and settle joists are attached as needed image 1.

Never install a ledger board over the top of siding no matter what you hear this can weaken the connection. The awning should be at least 7 to 8 feet above the ground or the patio. The screws should penetrate the ledger the sheathing the house and go into a framing beam such as a floor joist or a wall stud. Anchor deck joists to the ledger with joist hangers filling each hole with galvanized joist hanger nails rated for pressure treated wood.

Also you need to keep enough open space approximately 3 4 inches above the top of the mounting bracket and ledger board. Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. Once the ledger board is tightly fastened into place use a caulk gun to caulk all the seams between the ledger and the house with weatherproof caulk. Locate a position for a header or ledger board.

Make it the full width of the porch or slightly wider depending on your porch design. Predrill and sink 1 2 in. In order to install the ledger board you usually need to remove the house s siding. So make a mark above 7 to 8 inches and keep a minimum gap of 2 inches at one of the ends.

Attaching Ledger Board Pergola Pergola Kits Replacement Canopy

Attaching Ledger Board Pergola Pergola Kits Replacement Canopy

Attachingaledgertobrick Gif 382 322 Pixels In 2020 Building A Deck Exterior Brick Brick Wall

Attachingaledgertobrick Gif 382 322 Pixels In 2020 Building A Deck Exterior Brick Brick Wall

Corrugated Patio Cover Note This Is Not Attached To The House The Pergola Patio Covered Patio Building A Deck

Corrugated Patio Cover Note This Is Not Attached To The House The Pergola Patio Covered Patio Building A Deck

Pin By Wendy Haston On Porch Building A Deck Timber Deck Deck Framing

Pin By Wendy Haston On Porch Building A Deck Timber Deck Deck Framing

Source : pinterest.com